E-PLUS Image Release History
	Version	Release Date		Changes
	8.00.43	4/12/2021		1. Supported Foxboro Sensor Different Range
				2. Added ISO6976-2016 Heating Value (Gross Method)
	8.00.42	10/18/2019		1. Added Foxboro Transmitter Interface
	8.00.41	3/21/2019		1. Increased DP Resolution for 4-20mA Input
	8.00.40	5/30/2018		1. Reset Turbine Offset at Startup
	8.00.39	11/18/2016		1 .Added Calorific Calculation
				2. Corrected Energy Flow Calculation (Metric Units)
				3. Replaced Mass Units "TON" with "TONNE"
	8.00.38	11/25/2015		1. Added Last 24 Hours Chart
				2. Reset RAM after Loading the New Firmware
	8.00.37	9/4/2014		1. Added Modbus Registers 7024-7025
				2. Added Switch Output Wiring Selection
	8.00.36	2/7/2014		1. Added BS&W for Liquid Meter
				2. Correction - Reset Reynolds Number Flag if Not Used (Cone Meter)
	8.00.35	10/24/2013		1. Added Reynolds Number Linear Factors for SmartCone Meter
	8.00.34	10/29/2012		1. Modified Communication Routine
				2. Modified Sdevice Timer
				3. Corrected Spare#3/#4 in the Historical Report
				4. Added Modbus Address 7185-7187 Multivariable Numeric DP/Pressure/Temperature Value
				5. Reset Pressure/Temperature/BS&W Override Value if Nothing is Assigned to the Input
	8.00.33	5/14/2012		1.Added Accelabar Flow Equation (Natural Gas)
	8.00.32	4/27/2012		1. Correction - Display Assignments 43 and 44
				2. Modified Download Mode
	8.00.31	1/17/2011		1. Added Ammonia Equation
	8.00.30	6/29/2011		1. Added Zb and Z Factor
				2. Modified Status/Frequency Input Reinitialzation
	8.00.29	12/3/2010		1. New Display Contrast Initialization
	8.00.28	8/27/2010		1.Modified Display Contrast to Support Version1 and Version2 Display
	8.00.27	8/6/2010		1.Modified the Display Contrast
	8.00.26	4/28/2010		1. Added 16 Bits Registers for V-Cone Application
	8.00.25	3/31/2010		1. Added New Display Driver
				2. Modified Reset Routine
	8.00.24	1/28/2010		1. Modified to Display Guage Pressure Only
				2. Modified Serial Communication Routine
				3. Modified Enron Alarm/Event Routine
	8.00.23	11/1/2009		1. Added GE GHM80 Mass
	8.00.22	10/8/2009		1. Added CHOKE Equation
				2. Added Momentary Switch Output Option
	8.00.21	11/26/2008		1. Added VenCone Flow Equation
				2. Added BLM Display Option
	8.00.20	8/26/2008		1. Added Critical Control Registers
	8.00.19	4/12/2008		1. Correction - ISO5167 - 2003 Factors
	8.00.18	3/11/2008		1. Correction - Reset Spare Data Variables
	8.00.17	9/12/2007		1. Added ISO5167-2003 Equation
	8.00.16	9/12/2007		1. Correction - Historical Hourly Program Variables
	8.00.15	8/20/2007		1. Correction - Verification Report - RTD/Analog Inputs
	8.00.14	6/27/2007		1. Correction - External RTD Diagnosis
	8.00.13	6/15/2007		1. Added Factory Test
	8.00.12	10/6/2006		1. Correction - Wrong Version Number
				2. New Rosemount Average Rountine
	8.00.11	9/22/2006		1. Read Rosemount Transmitter Type
	8.00.10	8/16/2006		1. Correction - Bluetooth Re-Connection
				2. Disable Plunger Checking in Diagnostic Mode
				3. Add Plunger Start Delay Timer
	8.00.09	5/19/2006		1. Add Barrel Flow Unit Selection
				2. Correction - Plunger Lift Stage Flag
	8.00.08	5/3/2006		1. Add Saturated Steam Calculation
				2. Add Venturi Equation
				3. Add Plunger Lift Early Arrival Protection
				4. Add Audit Trail Entries - Date, Time, and Heating Value Override
				5. Add Bluetooth
	8.00.07	4/3/2006		1. Add Customer Storage Option
				2. Add Time Based Plunger Lift Control
				3. Add Flow Unit Selection - M3 and CF
	8.00.06	1/19/2006		1. Correction - Graphic Display - Daily FWA Value
	8.00.05	7/19/2005		1. Add Flow Set Point Selection for PID Control
	8.00.04	7/5/2005		1. Correction - Steam Energy Flow Calculation
				2. Correction - Display Unit is Based on the Flow Unit Selection
	8.00.03	3/22/2005		1. Add New Modbus Registers - Yesterday's Flow Time in Minutes and in Seconds
				2. Correction - Active Alarms (Display)
				3. Check SG Limit only if AGA8 Gross Method 2 Is Used.
				4. Add Graphical DFM Logo
	8.00.02	3/8/2005		1. Add - Daylight Saving Time Option
				2. Add - Steam Calculation
				3. Add - 5 Sets of Program Variable Statements
				4. Change - Save up to 840 Historical Hourly Reports.
	8.00.01	1/6/2005		1. Set Auxiliary Meter Default to Zero
				2. Add Orifice Plate Selector
				3. Add BS&W Input
	8.00.00	11/1/2004		1. First Release