MICROMS4 Image Release History
	Version	Release Date		Changes
	6.04.24	10/16/2025		1. Enabled Turbine Diagnostic Mode
	6.04.23	6/5/2025		1. Added Dynacone Wet Gas Flow Equation
				2. Added ISO6976-2016 Heating Value (Gross Method)
				3. Adjusted Timer
	6.04.22	5/4/2021		1.Supported Different Ranges of Foxboro Sensor
	6.04.21a	7/27/2020		1. Added Delay Timer for Polling a Slave Unit.
	6.04.21	5/30/2018		1. Reset Turbine Offset at Startup
	6.04.20	5/11/2018		1. Added Foxboro Transmitter Interface
				2.  Increased Timer for A/D Converter (Analog Inputs)
	6.04.19	10/16/2017		1. Added NIST10-Superheated Steam
				2. Adjusted Timer for A/D Converter
	6.04.18	11/2/2016		1. Corrected Energy Flow Calculation (Metric Units)
	6.04.17	12/2/2015		1 .Added Calorific Calculation
	6.04.16	9/1/2015		1. Modified Multivariable Data Dump Routine
	6.04.15	8/16/2015		1. Added Mutivariable Data Dump
	6.04.14	9/9/2013		1. Corrected Analog Input#3 Reading
	6.04.13	7/16/2013		1. Set Turbine Meter (GAS) to Liquid Meter Application if Composition Flag is Configured
	6.04.11	4/30/2013		1. Modified Communication Routine
				2. Reset Flow Averaged Value if a New Flow Calculation Method is Applied.
				3. Set Less Sensitivity Default Value for the Display Keys
	6.04.10	3/15/2013		1. Reduced Sdevice Timer
				2. Implemented API 2004 Crude Volume, Set Ct,anp to CTPL
				and set Base Density to Density@15 (Metric Units)
				3. New Display Contrast Initialization
				4. Display Analog Input Maintenance/Live Value without Setting High Limit (Fail Code=2)
				5. Set Double Write to Download Mode via RS232 Port
	6.04.09	10/25/2012		1. Modified Communcation Routine
	6.04.08	6/1/2012		1. Added Accelabar Equation
				2. Added Venturi Equation
				3. Correction AGA7 - Mass Flow
	6.04.07	12/16/2011		1. Correction - Poll Meter#2,#3, and #4 Historical Reports
				2. Allowing Zero Based Temperature
	6.04.06	2/20/2011		1. Activated Slave Port and Digital In/Output#4 (Model 2009 or Newer Board)
	6.04.05	4/28/2010		1. Added ISO 6976
	6.04.04	3/31/2010		1. Modified Reset Routine
	6.04.03	1/29/2010		1. Added Rosemount Meter Type
	6.04.02	9/16/2009		1. Modified Display Initialization
	6.04.01	5/29/2009		1. Addeed Pitot Tube Equation
				2. Added Modbus 2370 (1=New Hardware)
	6.04.00	3/25/2009		1. Addeed Support for Old and New Hardware Units
	6.03.16	3/6/2008		1. Modify Audit Trail Routine
				2. Correction - Read Analog Input Expansion Configuration
	6.03.15	11/14/2007		1. Correction - Reset Test Data - No Flow
	6.03.14	5/2/2007		1. Add - Gravity Factor and Base Density Factor
				2. Correction - Verabar Equation - Mass and Energy Flow Rate
	6.03.13	1/23/2007		1. Correction - Daily FWA BS&W
	6.03.12	1/8/2007		1. Modify Display Sensitivity Key Routine
	6.03.11	7/21/2006		1. Add BS&W Input Option
	6.03.10	11/4/2005		1. Correction - Update Analog Output mA Value
	6.03.9	4/29/2005		1. Add - Verabar Flow Equation for Gas and Liquid Application
	6.03.8	3/16/2005		1. Add - Daylight Saving Time Option
				2. Add 16 Bits Month, Day, Year, Hour, Minute, and Second Registers
	6.03.7	12/1/2004		1. Enable/Disable Front Panel Scan Key
				2. Add Turbine Diagnostic Data
				3. Add Calibration Parameters to be Part of the Configuration Software
	6.03.6	10/8/2004		1. Modify Modbus Shift Routine
				2. Modify Program Variable Statements and Boolean Statements Routine
	6.03.5	9/2/2004		1. Add Gas Composition Selection
				2. Add TPU Frequency Counters
	6.03.4	6/10/2004		1. Add Battery Voltage Reading
	6.03.3	5/21/2004		1. Correction - Broadcast Command
	6.03.2	5/18/2004		1. Correction - Update Gas Composition for All Meters On Snapshot Report.
				2. Correction - Liquid Meter Using AGA7 Method
	6.03.1	4/29/2004		1. Correction - Analog Output Display mA
	6.03.0	2/20/2004		1. Add 485 Port#2 or Digital Output#4 Option
				2. Correction - Slave ECHART or MICROMV Message Initialization
	6.02.9	1/21/2004		1. Correction - Update Gas Composition of Snapshot Report if G.C. is configured.
	6.02.8	1/2/2004		1. V-Cone Fow Equation - Add Y Factor Selection, Cone Thermal Coefficient
	6.02.7	12/2/2003		1. Correction - AGA7 Mass Calculation
	6.02.6	11/18/2003		1. Correction - Modbus IEEE Floating 2 Registers per One Variable (No. of Variables)
	6.02.5	10/27/2003		1. Set ROM/RAM Wait State to 1
	6.02.4	9/8/2003		1. Add Three Frequency Inputs Selection - AGA7
	6.02.3	8/28/2003		1. V-Cone Calculation -  Add Pipe and Cone Thermal Coefficient
	6.02.2	7/24/2003		1. Correction - Write Modbus Floating Point 2 Registers 4 Bytes Variables
				2. Improve Real Time Clock Accuracy
	6.02.1	7/15/2003		1. Add BS&W Override
				2. Add Natural Gas @20 Deg.C Flow Equation
				3. Add Liquid Crude Volume to 20 Deg.C Equation
	6.02.0	4/23/2003		1. Add Data Verification/Calibration Report
	6.01.9	3/7/2003		1. Correction - Update Liquid AGA7 Meter Factor and Frequency Data
	6.01.8	3/3/2003		1. Reset Slave Variables If Slave ID Is Changed Back To Zero.
				2. Default Display Timer to 4
	6.01.7	2/25/2003		1. Add Gas/Liquid Application Selection (Liquid - Table 24A, API 11.2.1)
				2. Add 4 Slaves-ECHART Interface
				3. Modify Foxboro Interface and calculation
	6.01.6	1/22/2003		1. Add 2368 IEEE Floating Point Modbus Selection 0=One 32 bits, 1=Two 16 bits Data
				2. Add 2368 IEEE Floating Point Modbus Sequence 0=HI,LO 1=LO,HI Bytes
				3. Add 7352 Day Start Hour
				4. Add Security Code Variables for the Window Program.
				5. Modify Foxboro Interface and calculation
	6.01.5	12/27/2002		1. Add Foxboro Interface
				2. Correction - Data Entry Through Front Panel Display
	6.01.4	12/19/2002		1. Normalize AGA8 Composition Percentage. (Acceptable Data Range 98-102)
				2. Add Gas or Liquid Application
				3. Add Flowing Density Override Entries
				4. Add Station Total Selection
				5. Correction - Program Variables
				6. Add Historical Data - Program Variables
				7. Enable PID Routine
				8. Add Previous Day's Gross, Net, Temperature, Pressure 32 Bits Integer Modbus Registers
	6.01.3	10/23/2002		1. Add Spare Data - RTD
	6.01.2	10/18/2002		1. Special Project - Test Data
	6.01.1	9/20/2002		1. Add New Data Entry - "Frequency I/O Postion Selection"
				2. Add "Test Data"